RESUMO O lodo de estação de tratamento de água (ETA), resíduo Classe II A, tem geração crescente, alto custo de tratamento e, quando descartado incorretamente no meio ambiente, acarreta danos ambientais. Assim, o objetivo do estudo foi analisar o emprego do lodo da ETA Santa Bárbara, da cidade de Pelotas/RS, beneficiado por calcinação a 600°C, como material suplementar ao cimento Portland. Amostras do lodo in natura e calcinado foram submetidas a ensaios de microscopia eletrônica de varredura e espectrometria de raios X por dispersão de energia, e foram determinadas a umidade do lodo in natura, a perda de massa e a massa específica do lodo calcinado. Realizaram-se ensaios de índice de atividade com cimento branco, cimento Portland de alta resistência inicial (CPV-ARI) e cal para identificar a atividade pozolânica do material. Posteriormente, foi executada a moldagem de dois traços de concreto, um de referência e outro com 10% em massa de substituição do aglomerante pelo lodo beneficiado, sendo analisadas as propriedades nos estados fresco e endurecido do concreto. Embora a incorporação do lodo tenha apresentado resultados favoráveis e aumento de resistência à compressão axial, o resíduo não pode ser classificado como pozolana por causa dos materiais e condições de ensaio empregadas na pesquisa. Contudo, com os resultados obtidos neste trabalho é possível averiguar que o uso do lodo beneficiado em matrizes de concreto é efetivo e constitui uma alternativa sustentável de destinação ao lodo de ETA.

ABSTRACT The sludge from the Water Treatment Plant (WTP), Class II A waste, has an increasing generation, high treatment cost and, when improperly disposed of in the environment, causes environmental damages. Thus, the objective of the study was to analyze the use of sludge from WTP Santa Bárbara, in the city of Pelotas, Rio Grande do Sul, benefited by calcination at 600°C, as a supplementary material to Portland cement. Samples of in natura and calcined sludge were subjected to SEM and EDS tests, the moisture of the in natura sludge was determined, and the loss of mass and specific mass of the calcined sludge. Activity index tests were performed with white cement, Portland cement CPV-ARI and lime, to identify the pozzolanic activity of the material. Subsequently, the molding of two concrete strips was carried out, one of which is a reference and the other with 10% by mass of substitution of the binder by the processed sludge, and the properties in the fresh and hardened state of the concrete were analyzed. Although the incorporation of the sludge has shown favorable results and increased resistance to axial compression, the residue cannot be classified as pozzolan to the detriment of materials and test conditions employed in the research. However, with the results obtained in this work it is possible to verify that the use of the processed sludge in concrete matrices is effective and constitutes a sustainable alternative for the disposal of WTP sludge.

Abstract: This study aims to evaluate chemical characteristics, antioxidant and antibacterial activities of organic compounds extracted from three Eucalyptus wood and Corymbia maculate wood using ethanol as a solvent. To obtain the ethanolic extracts, 15 g of a powdered wood sample was mixed with 150 mL of ethyl alcohol 99 % PA by constant mechanical stirring, which was further magnetically mixed at 60 ºC for 24 h. The extractives were analyzed utilizing percent yield, Fourier-transform infrared spectrum, inhibitory index (measured after antimicrobial tests), antioxidant activity, and condensed tannins content. The Eucalyptus dunnii extract showed the highest percent yield. The infrared spectra of all the extractives presented similar profiles, with remarkable bands ascribed to the presence of lipophilic extracts, sterols, fatty acids, and other hydroxylated substances, such as carbohydrates and phenolic compounds. In all cases, the higher the concentration of the extractive was, the higher the antioxidant activity was. The antioxidant activity of Eucalyptus saligna extract stood out since overcame that of the positive control (ascorbic acid). Regarding the condensed tannins content, that extract from Eucalyptus grandis excelled.

RESUMO As madeiras apresentam propriedades tecnológicas distintas, por ser material orgânico e heterogêneo, sendo necessário uma avaliação para o uso adequado. Sendo assim, o objetivo deste trabalho foi a avaliação de propriedades tecnológicas, sendo elas: massa especifica básica, massa especifica aparente a 12%, teor de umidade de equilíbrio, flexão estática (MOE e MOR), compressão paralela as fibras (Fc e Ec), análise colorimétrica, termogravimetria (TGA e DTG) e fourier transform infrared spectroscopy (FT-IR), das espécies de Corymbia maculata, Eucalyptus grandis, Pinus elliottii. Determinaram-se as propriedades tecnológicas conforme descrito nas normas ASTM D 2395-17 (2017) e ASTM D 143-94 (2014). Em relação as propriedades físico-mecânicas, as species apresentaram diferenças significativas baseadas em análises estatisticas, possuindo destaque a espécie de Corymbia maculata. Em relação a análise colorimétrica, foi verificado que a espécie Corymbia maculata possui uma coloração marrom-avermelhado, a espécie de Pinus elliottii amarelo com tonalidade clara, enquanto o Eucalyptus grandis avermelhada com tonalidade clara. Para o FT-IR foi constatado picos semelhantes entre as espécies, porém com intensidades distintas, sendo estes referentes as vibrações moleculares características dos componentes orgânicos da madeira. Por meio da análise termogravimétrica percebe-se que as espécies de Pinus elliottii e Corymbia maculata, apresentaram maior estabilidade térmica, quando comparadas ao Eucalyptus grandis, possuindo um menor percentual de perda de massa e um retardo de temperatura em relação ao pico máximo de degradação (DTG), próximo aos 400°C, sendo essas propriedades analisadas com testes ANOVA com significância de 5%. Sendo assim destaca-se uma heterogeneidade entre as espécies avaliadas nesse estudo, tanto do ponto de vista físico, mecânico, térmico e químico, fazendo-se necessário a caracterização de tais propriedades para o emprego correto destes materiais.

ABSTRACT The woods have distinct technological properties, as they are organic and heterogeneous material, requiring an assessment for proper use. Therefore, the objective of this work was the evaluation of technological properties, which are: basic density, apparent density at 12%, equilibrium moisture content, static flexion (MOE and MOR), parallel compression of the fibers (Fc and Ec), colorimetric analysis, thermogravimetry (TGA and DTG) and Fourier transform infrared spectroscopy (FT-IR), of the species of Corymbia maculata, Eucalyptus grandis, Pinus elliottii. The technological properties were determined as described in the ASTM D 2395-17 (2017) and ASTM D 143-94 (2014) standards. Regarding the physical-mechanical properties, the species showed significant differences based on statistical analysis, highlighting the species of Corymbia maculata. Regarding the colorimetric analysis, it was found that the species Corymbia maculata has a reddish-brown color, the Pinus elliottii species loves it with a light shade, while the Eucalyptus grandis reddish with a light shade. For FT-IR, similar peaks were found between species, but with different intensities, these being related to the molecular vibrations characteristic of the organic components of wood. Through thermogravimetric analysis, it can be seen that the species of Pinus elliottii and Corymbia maculata, presented greater thermal stability when compared to Eucalyptus grandis, having a lower percentage of mass loss and a delay in temperature in relation to the maximum peak of degradation ( DTG), close to 400 ° C, and these properties were analyzed with ANOVA tests with 5% significance. Thus, there is a heterogeneity among the species evaluated in this study, both from a physical, mechanical, thermal and chemical point of view, making it necessary to characterize these properties for the correct use of these materials.

Abstract: Organic substances have been used for different wood treatments, especially impregnation procedures, aiming at improve certain wood properties. The objective of this study was to evaluate dimensional stability and colourimetric features for a mature pine wood (Pinus elliottii) impregnated by vacuum-pressure process with variable concentrations (10 wt%, 25 wt% and 50 wt%) of furfuryl alcohol and using ethyl alcohol as catalyst. The wood samples were characterized for:linear shrinkages, linear swellings, shrinkage anisotropy, swelling anisotropy, as well as colorimetric parameters (following the CIELab method). The impregnation with furfuryl alcohol increased the dimensional stability of the studied pine wood and the treatment with a concentration of 50 wt% stood out based on these results. Regarding the colourpatterns, there were changes in the final colorimetric appearances of the treated wood samples, which acquired darker and reddish colours when compared to the pristine group. The treatment with 50 wt% of furfuryl alcohol also was responsible for the highest colour change and, because of that, may be indicated for solid wood products with high added value.

RESUMO As madeiras de Pinus apresentam características indesejáveis às quais podem ser atenuadas com a aplicação de tratamentos, no qual é destacado a furfurilação. Sendo assim, o objetivo deste trabalho foi avaliar o efeito da impregnação de álcool furfurílico nas propriedades físicas e mecânicas da madeira de Pinus elliottii. Para tanto, foram utilizados 4 tratamentos: controle e com diferentes cargas de álcool furfurílico (10%, 25% e 50%). Determinaram-se às propriedades tecnológicas conforme descrito nas normas ASTM D 2395-17 (2017) e ASTM D 143-94 (2014). Verificou-se que para as propriedades mecânicas, a resistência à compressão paralela às fibras, em que o parâmetro MOE teve um acréscimo significativo para todos os tratamentos em relação ao grupo controle, em destaque especial para o tratamento (TF25%), para o MOR obteve-se valores superiores, porém sem diferenças significativas. Em relação a dureza Janka, a tensão máxima no plano anatômico transversal, constatou-se valores superiores se comparados ao controle, com destaque o tratamento (TF50%), o qual demonstrou maiores valores com diferença significativa. Para o plano tangencial não foram constatadas diferenças significativas, se mantendo praticamente constantes os valores médios entre os tratamentos e o controle. Para flexão estática, MOR e MOE, não se observaram diferenças significativas, sendo essas propriedades analisadas com testes ANOVA com significância de 5%. Com isso pode-se concluir que a impregnação com álcool furfurílico foi eficaz, devido às melhorias de desempenho mecânico observado. Visto o potencial da furfurilação empregada na madeira com base nestes resultados, sugere-se mais pesquisar neste campo de modo a fomentar maiores informações sobre a utilização deste tratamento em madeira.

ABSTRACT Pinus wood presents undesirable characteristics that can be attenuated with the application of treatments, in which the furfurylation is highlighted. Therefore, the objective of this work was to evaluate the effect of impregnation of furfuryl alcohol on the physical and mechanical properties of Pinus elliottii wood. For this, 4 treatments were used: control and with different loads of furfuryl alcohol (10%, 25% and 50%). The properties were determined as described in ASTM D 2395-17 (2017) and ASTM D 143-94 (2014). It was verified that, for the mechanical properties, the compression resistance parallel to the fibers, in which the MOE parameter had a significant increase for all the treatments in relation to the control group, especially for treatment (TF25%), for the MOR, higher values were obtained, but without significant differences. Regarding Janka hardness, the maximum tension in the transverse anatomical plane, higher values were observed when compared to the control, with emphasis on treatment (TF50%), which showed higher values with significant difference. For the tangential plane, no significant differences were observed, maintaining the average values between the treatments and the control practically constant. For static flexion, MOR and MOE, no significant differences were observed, these properties being analyzed with ANOVA tests with significance of 5%. With this it can be concluded that the impregnation with furfuryl alcohol was effective, due to improvements in mechanical de-performance observed. Considering the potential of furfurylation employed in wood based on these results, it is suggested to do more research in this field in order to promote more information on the use of this wood treatment.